- INTEL 82578DC GIGABIT NETWORK CONNECTION HOW TO
- INTEL 82578DC GIGABIT NETWORK CONNECTION INSTALL
- INTEL 82578DC GIGABIT NETWORK CONNECTION DRIVERS
- INTEL 82578DC GIGABIT NETWORK CONNECTION UPDATE
Output of ethtool -i eth0 after the driver update (and before a reboot) Is there a way to make the new driver “stick” after a reboot ?įor the record, here's how I updated the network driver:ġ.Download latest e1000e driver from (in e1000e stable folder)Ģ.cd /home//Downloads (default folder for FireFox downloads) To get it back to work with the new driver I have to run sudo rmmod e1000e & sudo modprobe e1000e. The new driver works perfectly fine except that it reverts back to the old version after a reboot. The router I'm connecting to is Gigabit capable. I'm running Ubuntu 9.10 64-bit Desktop edition on a system with an Intel DP55WB motherboard (with integrated Gigabit NIC). My system starts at 10M instead of 1000M. My Ubuntu is a Ubuntu Server 9.10 and my installation is fresh this afternoon. Moreover, the transfers are very slow, I have an average of 2.4MB/s on a 3GB file, my network is GB and jai on another small server averaged 55MB/s. My system starts at 10M, I force 100M with ethtool, if I force 1000M, LAN card died (no more LEDs). e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: ethtool -s eth0 speed 100 duplex full autoneg ethtool eth0 TX packets:437924 errors:0 dropped:0 overruns:0 carrier:0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 By my assessment, all the important variables are the same.īoth fstab's mount the NAS with the same parameters too.ġ92.168.0.101:/data /media/NAS nfs rw,nolock 0 0īelow is the eth0 information from my DP55SBĮth0 Link encap:Ethernet HWaddr 00:1c:c0:f7:ab:9b My NAS to laptop can transfer 80 MBs in less than 10 seconds, but my NAS to this new Intel DP55SB takes 4-5 minutes. I updated my IGB but I see no difference.
INTEL 82578DC GIGABIT NETWORK CONNECTION DRIVERS
I found "Intel Wired Ethernet" linux drivers on the e1000 sourceforge project. However, even at 100 Mbps, I don't see speeds at all like my laptop that is also up at 100 Mbps. Upon boot, it starts at 10Mbps connection, and I can force it to 100 Mbps, using ethtool. I'm also experiencing this problem (mythbuntu 9.10) on my new Intel DP55SB motherboard. I can get it up from 10 to 100, but it won't go higher. Supported link modes: 10baseT/Half 10baseT/FullĪdvertised link modes: 10baseT/Half 10baseT/FullĮthtool -s eth0 speed 100 duplex full autoneg offĮthtool -s eth0 speed 1000 duplex full autoneg off e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: RX
SIOCGMIIREG on eth0 failed: Input/output errorĮth0: negotiated 100baseTx-FD flow-control, link okĠ0:19.0 Ethernet controller: Intel Corporation 82578DC Gigabit Network Connection (rev 05)
Advanced Driver Update also improves your PC experience by optimizing system memory, internet connection speed, fixing broken file extensions, removes duplicate files, high-performance defrag, locates and destroys undetectable malware varriants and optimizes your PC for maximum performance and.Linux boxer-04 2.6.31-17-generic #54-Ubuntu SMP Thu Dec 10 17:01: x86_64 GNU/Linux With access to over 3,000,000+ manufacturers world-wide, Advanced Driver Update can AUTOMATICALLY update all your devices in just '1 click'.
INTEL 82578DC GIGABIT NETWORK CONNECTION INSTALL
RECOMMENDED: Advanced Driver Update© PRO is designed to help you quickly install drivers directly from manufacturers using it's cutting-edge, device-matching technology.
INTEL 82578DC GIGABIT NETWORK CONNECTION HOW TO
How to Automatically Update Your Intel Networkįor users inexperienced with manually updating device drivers, it's recommended that you install an approved Microsoft driver utility to avoid all the pit-falls and complications involved.
0 kommentar(er)
